latest piece of kit

-
The Shack is looking cool with my latest addition.I am now the proud owner of a MFJ-969 Deluxe Versa Tuner II,this unit arrived from the USA courtesy of Hamcity.com and after paying the import tax it worked out that i saved £32. The MFJ-969 Antenna Tuner gives you MFJ's superb AirCore Roller Inductor and full 6 meteres through 160 Meter coverage!You get everything you've ever wanted including...300 Watts PEP SSB full featured antenna tuner, widest matching range, full size lighted Cross-Needle SWR/Wattmeter reads true peak forward power, QRM-Free PreTune, 8 Position antenna switch, built in 50 Ohm dummy load, heavy duty 4:1 balun -- all in a tough, attractive cabinet. MFJ's famous 1 year No Matter What warranty.
The MFJ-969 Antenna Tuner's AirCore Roller Inductor, gear driven turns counter and spinner knob gives you exact inductance control for absolute minimum SWR. MFJ's exclusive AirCore Roller Inductor has an air core that can't burn up! You get ultra-high-Q, the lowest loss, highest efficiency and highest power handling of any roller inductor in ham radio.
MFJ's exclusive Self-Resonance Killer Keeps potentially damaging self-resonances away from your frequency. Huge self-cleaning wiping contact gives you excellent low-resistance connection without contact arcing or burning.Solid 1/4 inch brass shaft, self-align bearings -- smooth non-binding operation.
The MFJ-969 Antenna Tuner covers all frequencies from 160 Meters thru 6 Meters, including the "magic band" -- the widest matching range of any full featured antenna tuner. Match dipoles, verticals, inverted vees, random wires, beams, mobile whips, SWL receiving antennas -- nearly any antenna. You can use coax cable, random wire or balanced lines. Has heavy duty 4:1 balun.
MFJ's new ActivePeak reading Circuit accurately reads true peak forward power -- an MFJ exclusive.
MFJ's lighted Cross Needle SWR/Wattmeter reads SWR, true peak forwards and average reflected power simultaneously on 300 Wat or 30 Watt ranges.
So ill be in test mode for the next week or so but it seems to be working well so far.73 to all DE 2E0HTS Simon

Comments

Post a Comment

Popular posts from this blog

New DX Contact 0n 12 Meters

-
Image
Today I managed a nice QSO with Tom ZD7X who is located at St. Helena which is quite a distance away from my location. I managed to work Tom ZD7X with a 5/9 report operating my FT-767GX with my home brew 20m delta loop assisted with the MFJ-969 to tune the antenna with 50 watts on 12 meters. 12M is rarely open and I have only had a few QSOs on this band so I guess the new Cycle has begun at last! Good DX de 2E0HTS 73
Read more

Full Size Delta Loop for 20M

-
Image
I came across a simple delta loop design courtesy of dxzone found on the net some time ago and have been planning to give it a go for a while. This weekend I had a couple of hours spare, so I decided to give it a go using some 2mm multi strand wire cable, a dipole centre and a mixture of 75 ohm and 50 ohm coaxial cable. The delta loop is supposed to be resonant on 20 meters but I found it to be a little high so at present I am tuning the Loop with my mfj-969 which copes extremely well. The resonant frequency is 13.2 MHz at the moment so the next chance I get, I shall shorten the overall length making sure that each of the three sides are still equal in length, and hopefully adjusting the antenna for maximum performance ATU free for 14.2 MHz. I believe the miscalculation in the resonant length is probably down to the fact that my wire is covered in the plastic sleeving from the manufacturer which always effects the swr as I have noticed in past experiments with dipoles you always get sl
Read more

Homebrew 40/80 Trap Dipole Design

-
Image
This Antenna design was one that I used about 4 years ago, it worked exceptionally well on 80m and 40m. The size of the antenna makes a Half wave length on 80 meters, and with the traps a half wave on 40m with a SWR (standing wave ratio) of 1:1-1.5 across both bands. It worked well also on 20m with the use of an A.T.U (antenna tuning unit). I made my version of this antenna using 3mm multi strand copper cable which I left covered by the PVC insulation. The traps can either be home brewed using some 40mm diameter plastic drain pipe and winding wire around the pipe approximately 10 turns, then connected in line after the 10 metre lengths. Or the alternative is to purchase some commercially made 7.1 MHz traps, and fit them in line the same way. The antenna can be fed with 50 ohm coax with a home brew balan or again a commercially purchased balan. The wire lengths of the dipole are 2x 10 metres and 2x 6.7 metres as shown on the diagram above. This antenna can be mounted quite low to the gr
Read more